Midis über RPG-Maker abspielen

Ich mir vor kurzem mal wieder das Midi "Opening2" aus dem Rtp über die Abspielfunktion des Makers angehört (Nicht im Spiel sondern über diese gelb Rote Note mit der Info "Select an play BGM for fun" (wenn man mit der maus drauf geht)). Das Opening is ja das Standart-midi beim Titel und hat in manchen Köpfen schon seine Spuren hinterlassen.

Also... Ich hab das Midi über diese abspielfunktion abgespielt. Da kam dieser markante anfang. Wers mal weiter gehört hat, weiss das danach ein part kommt der sich vom diesem nervenden anfang unterscheidet.

So und nun... Als ich es Abgespielt habe kam der anfang und dann dieser Part. Nach einer weile(Waren etwa 10 min) kams mir dann aber so vor als ob sich nur noch dieser Part wiederholt. Hab nochmal genau hingehört. Der Part wiederholt sich immernoch. Erst hab ichs noch in nem Testgame versucht. Das gleuiche ergebniss. Habs ausgeschaltet und bin in den RTP-Ordner gegangen und habs per Media-player aufgemacht. Die ganze Midi war nur 1:21 Lang. Es hätte auffallen müssen hätte sich auch wirklich alles wiederholt.



Jetzt meine Frage:
Hat der Maker irgendwie eine interne Abspielfunktion ab einer gewissen stelle, da es sich ständig ab der Mitte wiederholt?
Oder kann man Midis so manipulieren?

Zitat:

---

Zitat von http://www.gamingw.net/tutorials/157

If you've played video games before, you'll notice that many of the musical tracks play a short intro and then loop the melody over and over. Most of the RPG Maker 2000 default MIDIs also have this property. Normally, you'd only be able to achieve looping MIDIs by using Music Mucker (or Melody Raiser) 1999, but with the newer versions of Anvil Studio, you can do the same thing. In order to do this, you'll need the latest version of Anvil Studio (2002.08.03 or higher), and several MIDIs for editing. Make sure to create back-up copies of your MIDIs in case you mess up.



*** Steps to Making a Looping MIDI ***

Step 1: Install Anvil Studio if you haven't done so already.

Step 2: Save your MIDIs to the "Music" folder in your RM2K project.

Step 3: Run Anvil Studio and search for your MIDI, and then open it.

Step 4: Listen to your MIDI until you find a section that you want to repeat. When you reach the end of that section, or find that the section plays more than once, stop.

Step 5: Select View -> Composer from the top toolbar, and scroll back to the first note in the section that you want to repeat (if you have a Final Fantasy battle MIDI, you'd want to start the loop after the first note of that ever-familiar intro).

Step 6: Once you've found your starting point, select Edit -> Insert MIDI Controller Event from the top toolbar. A list of events pops up, which will allow you to change the dynamics of your MIDI, such as pitch bending and channel volume. The looping event goes under the code number "b06f", which is not in this list. In order to make it appear, you'll have to check the box that says "Show all controller events". When you do this, the "Kind of event" box will expand its list to show events that don't have official names. Move down the list until you find "Event: b06f". Set the channel to 1, and set the Control value to 111. This will set the event in place.

Step 7: Save your MIDI and listen to it thoroughly in RM2K. If you did the above steps correctly, you should hear your MIDI play, but instead of going back to the beginning of the song once it reaches the end, it should restart at the point where you inserted the MIDI.

Step 8 (optional): If you listen to your MIDI and something doesn't sound right (such as notes not playing again after fading out at the end), delete ALL of the notes at the end of the song EXCEPT those that you want to keep in your loop. You may have to go through all of the channels in your song in order to get this step right. For added precision, go to the first point in the song where the loop starts again, and memorize its position in the song (it will be shown underneath "Time" near the top of the screen), and make sure to delete all notes that play after that time. Save your MIDI when you're finished.

Step 9: Voilŕ! You're finished!



You can also use this MIDI controller to create songs that don't loop (such as short fanfares for victory, or when a person joins your party) by placing it at the end of the song.



*** Steps to Making a Non-Looping MIDI ***

Follow steps 1-3 for Looping MIDIs, and then do the following:

Step 4: Select View -> Mixer from the top toolbar, and scroll all the way to the end of the song.

Step 5: Select View -> Composer, and then Edit -> Insert MIDI Controller Event from the top toolbar.

Step 6: Check the box that says "Show all controller events", change the "Kind of Event" to "Event: b06f", the channel to 1, and the Control Value to 111.

Step 7: Save your MIDI and listen to it thoroughly in RM2K. If you did the above steps correctly, your MIDI should play all the way through, and stop once it hits the end.

Step 8 (optional): If you listen to your MIDI and there are still short notes (or drumbeats) playing at the end, you probably didn't set the controller far enough to the end. Make sure that it is placed at the VERY end of the song before saving and playing it in RM2K.

Step 9: Voilŕ! You're finished!

---

Have fun.